Menushopping cart
Tools for Working Wood
Invest in your craft. Invest in yourself.

JOEL Joel's Blog

How To Grind: Part 5 - Grinding the Hollow

02/01/2017



This is part 5 of a series on grinding:
Part 1: Introduction + When To Grind.
Part 2: The Technology of Grinding.
Part 3: Grinding Wheel Chemistry and Nomenclature.
Part 4: Dressing Your Grinding Wheel for Cool Running.
Part 5: Grinding the Hollow.
Part 6: Repairing a Damaged Edge Without Burning the Steel.

In the last section, we prepared our grinding wheel so we are ready to grind our chisel.

Before you grind, you have to make sure that the back of the chisel is flat. Now I don't mean flat for its entire length. I mean, from left to right at the cutting edge only - maybe a 1/16". ( Here is a blog about the reasons why you don't want to flatten the entire back.)

We need flatness at the edge so that the back will be an accurate reference for grinding. If the back isn't flat when we hollow grind, we would hit the edge at different points and not have a straight ground edge.

Next, we have to set the rest at the right angle. In general, I don't try to measure the angle; I try to maintain the current primary angle of the tool. Put the tool flat on the rest and rub it back and forth against the wheel of a grinder that is turned off. Rub it a few times to establish where you are making contact. A sharpie applied to the bevel will make the scratches more prominent. If the scratches are in the center of the bevel, then you are simply maintaining the current angle of the chisel. If the scratches are past the center towards the body of the chisel, you are increasing the grind angle. If you find yourself with scratches forward of the center, you will be shortening the bevel angle. This latter condition is bad for two reasons. One: you rarely need to shorten a bevel angle. Two: even worse, when you grind, you will hit the fragile thin tip of the chisel before you touch the back bevel, resulting in an uneven grind. And if you continue grinding at the tip, you will most certainly burn the steel. There is a simple technique for shortening the bevel without danger, but we will save that for next time when we discuss repairing damaged chisels.
How To Grind: Part 5 - Grinding the Hollow 1How To Grind: Part 5 - Grinding the Hollow 2How To Grind: Part 5 - Grinding the Hollow 3

To get the rest in the right place, I use a mixture of moving it carefully and tapping with a chisel handle. When I think I am done, I will put on my eye protection, make sure all loose clothing and hair is tied away, lower the shields (although for the purposes of clarity in these pictures the shields are retracted), put a large cup of water within arms-reach and get ready to turn on the grinder.

As with wheel dressing, I stand to one side when I turn on the grinder and let it come up to speed. Then, with the chisel on the rest, I touch the bevel to the wheel and then pick up the chisel to look to see where I actually made contact. If I am grinding where I want to be then I will continue, otherwise I will tap the rest to move it slightly, or possibly loosen the rest a very, very tiny amount so that then I can tap it to the right place. Be very careful here. In theory, you will only need at most a minor adjustment but it is easy to slip, especially if you have loosened the rest too much, or are twisting by hand too hard. The rest could turn into the wheel, jamming it, with disastrous results.

With the rest set correctly, I start grinding.

As you can see from the video, I place the chisel firmly on the rest and just going back and forth on against the wheel. Periodically I check to see how far I have gone, and if I neglect one spot or another, I pay more attention to it. In the beginning I concentrate on the center of the tool; as I get further along, I start grinding towards the sides. As I approach the edge, I am trying to work in a uniform way. My finger rests on the back of the chisel, and if it gets warm, I will instantly dunk the tool in a water bath. However with these CBN wheels (or a well dressed, crowned, 3X wheel) I find myself not needing to dunk frequently if at all. Paying attention to what is actually happening is the key here.

I typically grind to a wire edge, but many people don't, and leave a smidgen at the edge. In either case there isn't much to hone away.

In the last picture, you can see a chisel that was ground freehand against a crowned wheel. It probably isn't perfect, but it's pretty close. Any variance in my grinding will be straightened out instantly when I start honing on any flat stone.
How To Grind: Part 5 - Grinding the Hollow 4

Next week we'll show what do to for a damaged chisel or one for which we want a shorter angle. We need to remove a lot of metal without overheating the tip.

N.B. As you can guess from the video, I am new at video making. I'm still learning, but I hope even in this crude way the information is getting across.




Add a Comment
Comments are closed.
The opinions expressed in this blog are those of the blog's author and guests and in no way reflect the views of Tools for Working Wood.
Subscribe
JOEL Joel's Blog
BEN Built-It Blog
BREN Video Roundup
EVT Classes & Events
WORK Work Magazine
Newer Entries...
JOELOMG - 16th Century Boxwood Miniatures PT2 - and other news - 05/03/2017
JOELOMG - 16th Century Boxwood Miniatures PT1 - and other news - 04/26/2017
JOELSpooncarving and News - 03/29/2017
JOELHow to Use a Marking or Mortise Gauge (reprise) - 03/22/2017
JOELHow to Learn to Carve in the Modern Age - The Online Approach - 03/15/2017
JOELMitre Planes and the Finest of Mouths: Why? What Evidence? What to Look for When Shopping for Mitre and Shoulder Planes - 03/08/2017
JOELContext! - 03/01/2017
JOELMitre Planes and an Observation about Maker's Marks - 02/22/2017
JOELHow To Grind Part 6 - Repairing a Damaged Edge Without Burning the Steel - 02/08/2017
JOELHow To Grind: Part 5 - Grinding the Hollow - 02/01/2017
JOELHow To Grind: Part 4 - Dressing Your Grinding Wheel for Cool Running, Balance, and Convexity - 01/25/2017
JOELHow To Grind Part 3 - Grinding Wheel Chemistry and Nomenclature - 01/19/2017
JOELHow To Grind Part 2 - The Technology of Grinding -, Grinders, and Grinding Wheels - 01/11/2017
JOELHow To Grind - Part 1 - When To Grind - 01/04/2017
JOELHappy New Year, A Great Experience, Ideas for the New Year, & News - 12/28/2016
JOELNail - 12/21/2016
JOELThe Gramercy Tools Saw Etch Story - 12/14/2016
JOELHayward vs Hasluck, Ellis, & Jones - 12/07/2016
JOELA Failure to Communicate - 11/30/2016
JOELGuest Blogger: Chris Pye - Get A Grip - 11/23/2016
Older Entries...