Tools for Working Wood

 Joel's Blog at Tools for Working Wood

The Mechanics of Stropping - Why Stropping Works  

02/26/2013

In my last missive on the subject of sharpening I pointed out that when a tool has a belly for a bevel it's easy to sharpen ineffectively. The problem is of course that stones and sandpaper are hard surfaces and you get a point contact with anything except a straight line. Carvers have an even worse problem when sharpening any gouge. At best, with a perfectly straight bevel, they have at most a line of contact along the curvature of the gouge. There are tons of techniques for sharpening carving tools on a stone but for routine maintenance the go-to tool of every carver is a strop.

A strop is a piece of leather that is either plain or treated with a very fine abrasive. Unlike the hard surface of a stone, when you put your tool on the strop the leather gives, you get more than a point contact and you hone a much larger area of the tool at the same time. If you have treated your strop by rubbing it with a fine abrasive, usually in the form of a honing compound on a wax stick, you effectively make the strop into an abrasive hone that will conform to the curvature, both front to back and left to right or any edge tool.

The advantage to carvers is that with a strop you can sharpen faster and much easier than you can with stones. The advantage for cabinetmakers and joiners is that if your tool has a rounded bevel, or you were just sharpening ineffectively, you now have a way to actually sharpen at the cutting edge without having perfect technique. The strop glosses over inconsistencies in honing and gets you an edge, fast.

There is a trade off -- The bevel of the tool will be more rounded over time. This isn't a big deal for carving tools, but for cabinetmaker's tools you can easily round the bevel more or make the back of the tool convex. Another use for a strop is to wear away any wire edge the you created with your stones. However with a treated strop, which is an abrasive in itself, you also run the risk of creating even more wire edge. To solve that problem I use an untreated, that is plain, strop.
Another point to consider is your average honing compound is coarser than the best finishing stones. If you sharpen to 6000 grit, or with a diamond stone, a treated strop will be finer and give you a finer edge. However if you use a 8000 grit stone, and work it effectively, or a top notch Arkansas stone, a treated stop might make your tool duller. This is a problem that is easily dealt with but I think I should write a bit about strops themselves and stropping compounds. I'll do that in the near future.

When you strop you are stroking a fairly sharp cutting edge against an easily damaged piece of leather. In Maurice Fraser's article on sharpening he details techniques for effective stropping.

Tags:Woodworking Tools and Techniques
Comments: 3
02/26/2013DesertAl 
I'm confused. I thought the green honing compound was 0.5 microns average grit size. Since a Shapton 8000 grit stone is about 3 microns grit and a Shapton Pro is around 1.8 microns grit, how can those stones get a finer edge than a 0.5 micron loaded strop?
02/26/2013joel http://www.toolsforworkingwood.com
I'll go into detail about this some other time but the .5 micron of the compound is only a mean and the compound has a huge variance. Also for example - Shapton's 8000 grit is harder and a little larger than some of their competitors 8k (which is why Shapton's cut so fast but they recommend using so many stone grades). Most of the more usual water stones break down as you sharpen. As a matter of fact one brilliant piece of advice a famous Japanese planemaker said was that most people don't spend enough time on their finishing stone. The reason being is that as you work the slurry you get an effectively finer and finer grit. I started following this advice and he's right. Also in traditional Japanese sharpening they do not strop (or I am pretty sure they don't - I'll leave some wiggle room for myself there)
04/22/2013abraham 
@Joel.
The reason why the shapton and chosera stones cut that much faster, are a combination of the concentration of abrasive particles and the curing process that these stones are put through, in their manufacturing process. Their stones are also very closely graded, where there is not a large gap between the stated particular size of the stone.
Comments are closed.
The opinions expressed in this blog are those of the blog's author and guests and in no way reflect the views of Tools for Working Wood.
Subscribe
 Joel's Blog
 Ben's Blog
 Work Magazine
Recent Blogs:
Designing a Moxon Vise-10/15/2014
The Modern Split-10/01/2014
This Weekend: Maker Faire AND The Saturday Market Project at The London Design Festival-09/19/2014
The English Arts & Crafts Movement-09/17/2014
Maker Faire 2014 - Sept 20-21, NYC - My presentation-09/10/2014
Woodwork On The Streets - And Other News-09/03/2014
Ken Hawley, MBE 1927-2014-08/21/2014
King Lear and the Common-07/30/2014
Summer Reading: Factory Man-07/16/2014
The Hand and Eye Blog and some FYI's-06/19/2014
Relentless Self Promotion (and a Small Freebie)-06/11/2014
Lettercarving In Wood and Chris Pye's Free Offer. -05/28/2014
Handworks May 2015, Amana IA - Probably a Bad Idea-05/21/2014
NYC Design Show at Industry City-05/14/2014
Gehard Demetz - Woodcarvings in Chelsea - and Other News-05/07/2014
Festool Domino Sale - Machines and Accessories 10% off May 1 - June 30th 2014-05/01/2014
Automation and Carpal Tunnel Syndrome-04/23/2014
English Mortise Chisels - Mid-18th Century to Now - Part 5 - How to Handle a Chisel-04/17/2014
English Mortise Chisels - Mid-18th Century to Now - Part 4 - Chisel handles-04/15/2014
English Mortise Chisels - Mid-18th Century to Now - Part 3 - The Body of The Tool-04/10/2014
Older Entries...
Some Interesting Woodworking Blogs
Adam Cherubini
Tom Fidgen
Full Chisel Blog
Heartwood
Hock Tools - The Sharpening Blog
Norse Woodsmith
Jeff Peachy (book conservation)
Pegs and 'Tails
The Produce Savant
Konrad Sauer
Another Chris Schwarz Blog
Robin Wood Woodcraft
Rude Mechanicals Press(Megan Fitzpatrick)
UnpluggedShop.com - Hand Tool News
The Woodshop Bug
Chris Schwarz
Some Woodworking Forums
Family Woodworking
Knots
Saw Mill Creek
Wood Central
WoodNet
Woodwork Forums (Australia)
UK Workshop