|Along with other sets of carving tools we stock the Chris Pye sets of basic carving tools. But don't think this blog is merely a plug to sell that particular set, it's not. As a professional iron monger I do want you to buy tools, lots of tools, and from my company, not from the guy down the street. But, that being said, if I don't sell you the right tools, especially when you are starting out, then we will lose you as a customer, and of course we earn roughly the same amount of money no matter what you buy so it is in everyone's interest that when asked (and this happens on a daily basis) we recommend the right stuff. |
Here is the problem: Just about anyone on the planet who teaches carving recommends between a half dozen to a dozen tools to start out with but nobody agrees on WHICH half dozen or dozen tools to start with. There is a overlap of course, but different teachers teach different ways, different techniques, and also within the world of carving there are tons of different approaches. Also, teachers as a group would much rather their students start out with the same tools each time so that students can easily follow along with the examples and exercises that the teacher assigns.
In my case, my teacher Chris Pye wanted me to have the following tools to start so that I could do the first exercises in "Woodcarving Course & Reference Manual": #39 V 60Â° tool x 3/8in. 10mm, #2 Skew chisel x 3/8in. 10mm, #7 x 1/2in 14mm, #5 x 3/8in. 10mm, and a #9 x 1/8in. 3mm.
As it happened we were out of the stock at the time on the Ashley Iles #39 3/8" so I am using a 5/16" instead which turned out to be fine. Pye's seven piece set from Auriou, which I mention above - has very little overlap with the tools I needed for the exercises. A year later , since I already have the tools I need and then some, I don't need the set. But for a lot of people just starting out getting the set solves a lot of choice making.
Unless you are studying with someone else than Chris Pye.
We also stock a York set from Ashley Iles, which contain similar but not the exact tools than the Pye set and is perfectly good set of tools to start with. Another option is are sets of tools from Two Cherries which also come highly recommended. Incidentally if you are studying lettercarving or doing bigger or smaller stuff the basic sets aren't for you anyway. (We will have a special set of Chris Pye's recommended lettercarving tools available in the new year. I might get a set of those I think.)
We don't have an axe to grind on which tools to get so we give a 10% discount on 6 or more on Ashley Iles tools bought at the same time. This way you can make up your own set.
During the first weeks of class, as your teacher is teaching a wide variety of cuts and holds and you get your first hopefully broad range of assignments you will be using the entire set of tools the teacher recommended. Then everything changes. As you figure out what you like to carve you will also begin to figure out which tools you need. More large tools, more small tools, Full sets of sweeps because you are doing lots of curves. Big wide chisels for lettercarving, it varies from person to person and it is hard to predict.
What you should do is buy tools as you need them. If you make a mistake and find out you don't use the tools you have a year to return them. More importantly you have a year to figure out if the tool speaks to you.
A suggestion: If you get a mess of tools all at one go - from any vendor - even if they come sort of sharp they probably won't be classroom ready sharp. Using Chris's term, you have to "commission" your tools. It may seem to make sense to sharpen everything up at once but don't. The reason is that being a beginner it better to first sharpen the first few tools from start to finish, get them working correctly, work on your sharpening skill, correct any problems, and then sharpen the rest when you know what you are doing.
If you are not studying with a teacher and you are learning from a book getting the tools as you need them, or making up your own set is what we recommend. You can learn and do amazing things with one tool, or two, or whatever works with your budget. The five tools the Chris recommended to me for my studies took me through all the basic exercises and as I have gotten more practice I'm adding a few tools as I feel I need them for specific projects. I really try to justify each purchase because it's easy to get carried away. Most of the time it makes sense to adapt your project to use whatever tools you have on hand. And of course the fewer tools you have, the fewer need to be kept sharp and readily accessible.
|Comments are closed.|